![]() Select a Drive Letter and type in the folder that you’d like to connect to. In Windows 10, open This PC and select Map Network Drive. You can now access the mapped drive from Windows File Explorer on your computer. The steps below will walk through how to map the Synology NAS’s shared folder to Windows 10 or 11.Check the summary of your network drive.Tick the Reconnect at logon checkbox if you want the network drive to automatically reconnect each time you log in to Windows. Select a letter you want to use for your network drive.Select the shared folder you want to connect to and click Next.Enter your username and password and click Next.Launch Synology Assistant on your computer.Ping is a network utility that sends an echo request packet to an IP address and then waits for a reply. Modify your user name or disable Windows Hello. Update your computer to the latest version of Windows. If you don't have a static IP, open a free account with DuckDNS on 1.2.3.4 (example,. You have to forward port TCP 445 to 1.2.3.4's TCP 445. Go to the Download Center > select your Synology NAS model > Desktop Utilities to download and install Synology Assistant. If you are unable to map network drives when Windows Hello is enabled, try the following: Update your Synology NAS to DSM 6.2 or above. Yes, you can directly reach your shared folder from Windows Explorer as if you are home.Refer to the On your Synology NAS section in this article to avoid such configurations. There are additional DSM settings that may block SMB access.Make sure that your user account has Read/Write or Read only permissions for the shared folder that you want to map as a network drive.In Control Panel > Security > Firewall > Edit Rules, make sure that your firewall rules allow traffic on network ports used by Windows file server (i.e., ports 137, 138, 139, and 445). This tutorial looks at how to map a network drive on Windows using a Synology NAS. ![]() For DSM 6.2: Control Panel > File Services > SMB/AFP/NFS > SMB. 1 Do step 2, step 3, or step 4 below for how you would like to map a network drive in This PC.For DSM 7.0: Control Panel > File Services > SMB > SMB.Or 2.2 You could directly put the ip address of NAS into the address bar of Windows file explorer by NASIPaddress. Make sure that Enable SMB service is ticked at the following locations: 1.5.2 The shared folder is now mounted as a network drive.The problem is that I don't see any buttons anywhere to help me accomplish this. The backup apps I've downloaded to my UnRaid seem to only support talking to network drives this way. I have HDD attached to my router at //Servername/share and I want to "map" that drive on my UnRaid server so it'll show up as a "local" resource. Select Advanced Sharing from the Sharing tab: Figure 2: Share the demo folder using the Advanced Sharing options. After you create the folder, right-click it and choose Properties. Create the demo folder: Figure 1: Create a folder named demo. So here is my very basic problem that I couldn't find help for on the forum when searching for "map network drive" or "map drive" The steps to share the folder are displayed below. I don't want to pay for cloud storage and if my house burns down I'll have bigger problems. How to map a network drive on windows over the internet (outside LAM) So I would like to map my Synology NAS as a network drive over the internet (not lan) I enabled UPnP on my router I enabled DDNS on my synology driver in the DSM settings I enabled all the file services under ControlPanel>External Access>Router configuration. docker run -it -p 1880:1880 -v nodereddata:/data. Sure, it's RAID, but I'd feel better if the system backed up the data to an external network share on another server just in case. Then just run the following command to pull the image (tagged by 1.2.0-10-arm32v7 ), and run the container. Install Docker on your Linux installation by following the official documentation: https. So now I want to upgrade to the new 6.4.x soon, but before I do so, I thought it would be a good idea to backup my backup. For macOS see this, for Windows see this and for Synology see this. I'm new to UnRaid, not a Linux SysAdmin, and was attracted to this product because it seemed like a point/click kinda thing and so far I've been updating my plugins and every few months I check my array consistency and all reports happy.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |